创建VLAN 接口：vlan vlan_id
创建Tunnel 接口：tunnel tunnel_id
创建Channel 接口：channel channel_id
创建Redundant 接口：rint rint_id
创建虚拟接口：veth veth_id
创建Loopback 接口：loopback lo_id
创建PPPoE 接口：pppoe pppoe_id
删除任何接口使用，unset 来删除，注意的是只能删除当前未使用的接口。如果接口在使用中，请先停止在删除。
进入以太网接口配置模式：interface ethernet ethernet_id
启用以太网接口：unset shutdown
禁用以太网接口：shutdown
设置以太网接口的速率和双工模式：speed {10 | 100 | 1000 | auto} duplex {half | full | auto}
设置以太网接口的流量控制：flow control {on | off}
修改以太网接口的MAC 地址：mac address mac_address
获取以太网接口的默认MAC 地址：default mac
设置以太网接口的模式：working-type {layer2-interface | layer3-interface | layer3-shared-interface}
设置以太网接口的工作模式：port mode {access | trunk}
设置以太网接口隶属于指定的VLAN：port access vlan vlan_id
设置Trunk 端口所允许的VLAN：port trunk allowed vlan vlan_id_list
设置Trunk 端口所允许的Native VLAN：port trunk native vlan vlan_id
删除以太网接口所隶属的VLAN：unset port access vlan
删除Trunk 端口所允许的VLAN：unset port trunk allowed vlan vlan_id_list
删除Trunk 端口所允许的Native VLAN：unset port trunk native
修改三层以太网接口的最大传输单元：mtu {default | mtu_value}
将三层以太网接口设置为专用管理口：management-only
取消三层以太网接口的专用管理口设置：unset management-only
添加三层以太网接口的IP 地址：ip address ip_address netmask [webauth] [secondary]
删除三层以太网接口的IP 地址：unset ip address [ip_address netmask]
启用三层以太网接口的sFlow 功能：sflow enable instance instance_name direction {inbound | outbound | eitherbound}
禁用三层以太网接口的sFlow 功能：sflow disable
添加、修改或删除以太网接口的备注信息：description [string]
进入VLAN 接口配置模式：vlan vlan_id
启用VLAN 接口：unset shutdown
禁用VLAN 接口：shutdown
修改VLAN 接口的MAC 地址：mac address mac_address
获取VLAN 接口的默认MAC 地址：default mac
设置隶属于VLAN 的二层接口：hold {ethernet interface_id | channel channel_id_list | rint rint_id_list | veth veth_id_list}
删除隶属于VLAN 的二层接口：unset hold {ethernet interface_id | channel channel_id_list | rint rint_id_list | veth veth_id_list}
修改VLAN 接口的最大传输单元：mtu {default | mtu_num}
添加VLAN 接口的IP 地址：ip address ip_address netmask [webauth] [secondary]
删除VLAN 接口的IP 地址：unset ip address [ip_address netmask]
启用VLAN 接口的sFlow 功能：sflow enable instance instance_name direction {inbound | outbound | eitherbound}
禁用VLAN 接口的sFlow 功能：sflow disable
添加、修改或删除VLAN 接口的备注信息：description [string]
进入Tunnel 接口配置模式：tunnel tunnel_id
启用Tunnel 接口：unset shutdown
禁用Tunnel 接口：shutdown
修改Tunnel 接口的最大传输单元：mtu {default | mtu_num}
添加Tunnel 接口的IP 地址：ip address ip_address netmask [secondary]
删除Tunnel 接口的IP 地址：unset ip address [ip_address netmask]
借用其他三层接口的IP 地址：Unnumbered l3_interface_name
取消借用其他三层接口的IP 地址：unset Unnumbered
启用Tunnel 接口的sFlow 功能：sflow enable instance instance_name direction {inbound | outbound | eitherbound}
禁用Tunnel 接口的sFlow 功能：sflow disable
添加、修改或删除Tunnel 接口的备注信息：description [string]
进入Channel 接口配置模式：channel channel_id
启用Channel 接口：unset shutdown
禁用Channel 接口：shutdown
设置隶属于Channel 接口的二层以太网接口：hold ethernet interface_id
删除隶属于Channel 接口的二层以太网接口：unset hold ethernet interface_id
修改Channel 接口的MAC 地址：mac address mac_address
获取Channel 接口的默认MAC 地址：default mac
设置Channel 接口的模式：working-type {layer2-interface | layer3-interface | layer3-shared-interface}
设置Channel 接口的工作模式：port mode {access | trunk}
设置Channel 接口隶属于指定的VLAN：port access vlan vlan_id
设置Trunk 端口所允许的VLAN：port trunk allowed vlan vlan_id_list
设置Trunk 端口所允许的Native VLAN：port trunk native vlan vlan_id
删除Channel 接口所隶属的VLAN：unset port access vlan
删除Trunk 端口所允许的VLAN：unset port trunk allowed vlan vlan_id_list
删除Trunk 端口所允许的Native VLAN：unset port trunk native
修改三层Channel 接口的最大传输单元：mtu {default | mtu_num}
添加三层Channel 接口的IP 地址：ip address ip_address netmask [webauth] [secondary]
删除三层Channel 接口的IP 地址：unset ip address [ip_address netmask]
启用三层Channel 接口的sFlow 功能：sflow enable instance instance_name direction {inbound | outbound | eitherbound}
禁用三层Channel 接口的sFlow 功能：sflow disable
添加、修改或删除Channel 接口的备注信息：description [string]
进入冗余接口配置模式：rint rint_id
启用冗余接口：unset shutdown
禁用冗余接口：shutdown
设置主备物理接口：hold ethernet primary interface_id secondary interface_id
删除冗余接口的主备物理接口：unset ethernet
修改冗余接口的MAC 地址：mac address mac_address
获取冗余接口的默认MAC 地址：default mac
设置冗余接口的模式：working-type {layer2-interface | layer3-interface | layer3-shared-interface}
设置冗余接口的工作模式：port mode {access | trunk}
设置冗余接口隶属于指定的VLAN：port access vlan vlan_id
设置Trunk 端口所允许的VLAN：port trunk allowed vlan vlan_id_list
设置Trunk 端口所允许的Native VLAN：port trunk native vlan vlan_id
删除冗余接口所隶属的VLAN：unset port access vlan
删除Trunk 端口所允许的VLAN：unset port trunk allowed vlan vlan_id_list
删除Trunk 端口所允许的Native VLAN：unset port trunk native
修改三层冗余接口的最大传输单元：mtu {default | mtu_num}
添加三层冗余接口的IP 地址：ip address ip_address netmask [webauth] [secondary]
删除三层冗余接口的IP 地址：unset ip address [ip_address netmask]
设置冗余接口的探测方式：monitor type {icmp | arp} interval monitor type {icmp | arp} interval interval_time threshold num ip address ip_address
删除冗余接口的探测方式：unset monitor type {icmp | arp} ip address ip_address
设置冗余接口的故障恢复等待时间：wait-time wait_time
启用三层冗余接口的sFlow 功能：sflow enable instance instance_name direction {inbound | outbound | eitherbound}
禁用三层冗余接口的sFlow 功能：sflow disable
添加、修改或删除冗余接口的备注信息：description [string]
进入PPPoE 接口配置模式：pppoe pppoe_id
启用PPPoE 接口：active on
禁用PPPoE 接口：active off
配置拨号用户：username user_name password passwd
删除拨号用户：unset user
配置拨号方式：mode {auto | ondemand} [attempts {num | default} [interval {interval_time | default}] | interval {interval_time | default} [attempts {num | default}]]
配置拨号空闲时间：mode ondemand idle {idle_time | default}
取消拨号方式配置：unset mode
添加PPPoE 接口的IP 地址：ip address ip_address
删除PPPoE 接口的IP 地址：unset ip address
设置AC 名称：acname ac_name
删除AC 名称：unset acname
设置服务名称：servicename service_name
删除服务名称：unset servicename
设置隶属于PPPoE 接口的二层以太网接口或二层冗余接口：hold {ethernet interface_id | rint rint_id}
删除隶属于PPPoE 接口的二层以太网接口或二层冗余接口：unset hold {ethernet interface_id | rint rint_id}
覆盖系统默认网关：overwrite-default-gateway
取消覆盖系统默认网关：unset overwrite-default-gateway
覆盖系统DNS：overwrite-dns
取消覆盖系统DNS：unset overwrite-dns
启用PPPoE 接口WebAuth 认证：webauth
禁用PPPoE 接口WebAuth 认证：unset webauth
启用PPPoE 接口的sFlow 功能：sflow enable instance instance_name direction {inbound | outbound | eitherbound}
禁用PPPoE 接口的sFlow 功能：sflow disable
添加、修改或删除PPPoE 接口的备注信息：description [string]
